PCB 1.3 (English): Unterschied zwischen den Versionen

Aus www.wiki.ardumower.de
Wechseln zu: Navigation, Suche
(Schematics, Drawings, Photos)
(Schematics, Drawings, Photos)
Zeile 8: Zeile 8:
 
=Schematics, Drawings, Photos=
 
=Schematics, Drawings, Photos=
 
*[https://github.com/Ardumower/ardumower/raw/master/pcb/Produzierte_Platinen/megashield_svn_1.3_geschlossen/schematics/schematics.pdf Schematics]
 
*[https://github.com/Ardumower/ardumower/raw/master/pcb/Produzierte_Platinen/megashield_svn_1.3_geschlossen/schematics/schematics.pdf Schematics]
*[https://github.com/Ardumower/ardumower/raw/master/pcb/Produzierte_Platinen/megashield_svn_1.3_geschlossen/assemble/assemble_top.pdf Assemble, Jumpers top]
+
*[https://github.com/Ardumower/ardumower/raw/master/pcb/Produzierte_Platinen/megashield_svn_1.3_geschlossen/assemble/assemble_top.pdf Assembly, Jumpers top]
*[https://github.com/Ardumower/ardumower/raw/master/pcb/Produzierte_Platinen/megashield_svn_1.3_geschlossen/assemble/assemble_bottom.pdf Assemble, Jumpers bottom]
+
*[https://github.com/Ardumower/ardumower/raw/master/pcb/Produzierte_Platinen/megashield_svn_1.3_geschlossen/assemble/assemble_bottom.pdf Assembly, Jumpers bottom]
 
*[https://github.com/Ardumower/ardumower/raw/master/pcb/Produzierte_Platinen/megashield_svn_1.3_geschlossen/Platinenbilder/Platine_aus_11_Einzelbildern_zusammengesetzt.jpg PCB image]
 
*[https://github.com/Ardumower/ardumower/raw/master/pcb/Produzierte_Platinen/megashield_svn_1.3_geschlossen/Platinenbilder/Platine_aus_11_Einzelbildern_zusammengesetzt.jpg PCB image]
 
*[http://www.ardumower.de/index.php/de/forum/anleitungen-hilfe/633-workaround-fuer-ardumower#13004 Photos]
 
*[http://www.ardumower.de/index.php/de/forum/anleitungen-hilfe/633-workaround-fuer-ardumower#13004 Photos]

Version vom 12. Juli 2017, 14:32 Uhr

Steps

Pcb1 3.jpg

This page describes how to assemble PCB 1.3, how to add modules and how to configure the PCB.

NOTE: WE ARE CURRENTLY WORKING ON THIS PAGE - PLEASE LOOK AT PCB 1.2 FOR MISSING INFORMATION

Schematics, Drawings, Photos

Videos

Checklist

  • only set jumper JP1 (9V power) after you have manually set and measured the correct voltage (9v) at DC/DC Vout pin
  • set jumper JP13 on PCB back side for a Marotronics Arduino Due (i.e. Due clone) for automatic reset
  • set jumper JP12 (GPS signal voltage) to 3.3VP for Marotronics GPS module
  • set jumper JP7 (GPS operating voltage) to 5VP for Marotronics GPS module
  • set jumper JP10 (Bluetooth signal voltage) to 3.3VP for Marotronics Bluetooth module
  • set jumper JP4 (Bluetooth operating voltage) to 5V for Marotronics Bluetooth module
  • set jumper JP6 (WIFI operating voltage) to 3.3V for Marotronics WIFI module
  • set jumper JP11 (WIFI signal voltage) to auf 3.3V for Marotronics WIFI module
  • set jumper JC2 (IMU signal voltage) to 3.3V for Marotronics IMU module
  • only set I2C jumpers JC2, JC3, JC4, JC5, JC6, JC7 (at the top) if there is a corresponding I2C module installed
  • set jumper JP8 to 'Always-ON' for tests and for Arduino uploads, for regular operation (and automatic undervoltage power-off) to 'Automatic'
  • RTC module must be installed for proper I2C bus operation
  • press button P20 to power-on PCB

Forum

http://www.ardumower.de/index.php/de/forum/ardumower-pcb/1348-building-instruction-for-the-1-3-board