Chassis 2021: Unterschied zwischen den Versionen
BenPan (Diskussion | Beiträge) (→Tools) |
BenPan (Diskussion | Beiträge) |
||
| Zeile 17: | Zeile 17: | ||
#[https://www.youtube.com/watch?v=P06tg1YPgXk Ardumower Tutorials Chassis 2021 Teil 2 Vorbereitung] | #[https://www.youtube.com/watch?v=P06tg1YPgXk Ardumower Tutorials Chassis 2021 Teil 2 Vorbereitung] | ||
#[https://www.youtube.com/watch?v=s_W-PYmOGCo Ardumower Tutorials Chassis 2021 Teil 3 Montage] | #[https://www.youtube.com/watch?v=s_W-PYmOGCo Ardumower Tutorials Chassis 2021 Teil 3 Montage] | ||
| + | |||
| + | =Tools= | ||
| + | |||
| + | * Screw driver | ||
| + | * Different Imbus screw driver | ||
| + | * Different Torx screw driver | ||
| + | * Knife | ||
| + | * Round and flat file | ||
| + | * sand paper or sand sponge | ||
| + | * Drill machine with drill set (3,4,6,8,10 mm drills) | ||
=Whats inside the Box?= | =Whats inside the Box?= | ||
| Zeile 54: | Zeile 64: | ||
[[File:Chassis2021EmergencyStop.png | 500px]] | [[File:Chassis2021EmergencyStop.png | 500px]] | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
=Case assembly= | =Case assembly= | ||
Version vom 28. April 2021, 23:30 Uhr
This page is under construction.
This page describes the assembly of the Ardumower chassis that you can purchase via the shop 
.
Please start watching the detailed instruction videos on Youtube (see section "Videos"). This page is based on the content of the videos.
Inhaltsverzeichnis
Ardumower Chassis 2021 specifications
Videos
- Ardumower Tutorials Chassis 2021 Teil 1 WasGehoertDazu
- Ardumower Tutorials Chassis 2021 Teil 2 Vorbereitung
- Ardumower Tutorials Chassis 2021 Teil 3 Montage
Tools
- Screw driver
- Different Imbus screw driver
- Different Torx screw driver
- Knife
- Round and flat file
- sand paper or sand sponge
- Drill machine with drill set (3,4,6,8,10 mm drills)
Whats inside the Box?
Plates etc.
Electronics, Screws
Preparation of Plate-Materials
parts with sharp burrs
parts without sharp burrs
glue the doubled Motor-mounting-plates
Front-Plate
Mount the three Sonar-Sensors with hot-glue (carefully).
Mow-Plate
Inserting the threaded sleeves for the mower blades.
1
2
3
Wiring
There are two options to wire the emergency switch. Option 2 is the recommended version. If you realize version 1, don´t forget an external accessible power-Switch (close to "connector") .
Case assembly
Arrange parts and drill two holes for bumper cabling (see right hand finger for one of the marks)
Mount profiles to baseplate and gear-motors to side walls (with especially marked screws "Motor")
Mount profile for mowing motor
Install sealing ring
install mowing motor
mount sidewalls
prepare backside
install backside
prepare bumper
start with screws -> washers -> plastic spacer sleeves
add bumper -> washers -> nuts
finished bumper
install mowing plate
install frontplate
finished case
install electronics
final frontplate
final backplate
final top view
