Chassis 2021: Unterschied zwischen den Versionen

Aus www.wiki.ardumower.de
Wechseln zu: Navigation, Suche
(→‎Motor bearing is stiff)
(→‎Maintenance & Repair Tips)
Zeile 91: Zeile 91:
 
File: Chassis2021Assembly18.png | final backplate
 
File: Chassis2021Assembly18.png | final backplate
 
File: Chassis2021Assembly19.png | final top view
 
File: Chassis2021Assembly19.png | final top view
−
</gallery>
 
−
 
−
=Maintenance & Repair Tips=
 
−
 
−
==Clamping element will not tighten shaft anymore==
 
−
If your 'clamping' element will not tighten shaft anymore (e.g. due to a slightly reduced shaft diameter), you may:
 
−
 
−
* press together the outer clamping element in a bench vise
 
−
* OR use a filling under the 'ring'. Soda/beer can strip works fine for that. Wedged parts has slits, make sure those are not towards each other nor towards shaft d-slot.
 
−
* OR add a heat shrink tubing over the inner clamping element as shown in the photo (NOTE: this is a temporary solution and may not last forever as the heat shrink tubing may dissolve over time):
 
−
 
−
<gallery>
 
−
File: clamping_element_tube2.jpg
 
−
File: clamping_element_tube1.jpg
 
−
File: clamping_element_tube3.jpg
 
 
</gallery>
 
</gallery>
  

Version vom 6. September 2021, 21:03 Uhr


This page describes the assembly of the Ardumower chassis that you can purchase via the shop Shopping.png.

Related pages:

Ardumower chassis2021 weiß.jpg

Please start watching the detailed instruction videos on Youtube (see section "Videos"). This page is based on the content of the videos.



Videos

  1. Ardumower Tutorials Chassis 2021 Teil 1 WasGehoertDazu
  2. Ardumower Tutorials Chassis 2021 Teil 2 Vorbereitung
  3. Ardumower Tutorials Chassis 2021 Teil 3 Montage

Tools

  • Screw driver
  • Different Imbus screw driver
  • Different Torx screw driver
  • Knife
  • Round and flat file
  • sand paper or sand sponge
  • Drill machine with drill set (3,4,6,8,10 mm drills)

Whats inside the Box?

  • Plates etc.

  • Electronics, Screws

Preparation of Plate-Materials

  • parts with sharp burrs

  • parts without sharp burrs

  • glue the doubled Motor-mounting-plates

Front-Plate

Mount the three Sonar-Sensors with hot-glue (carefully).

Chassis2021Prepare4.png

Mow-Plate

Inserting the threaded sleeves for the mower blades.

  • 1

  • 2

  • 3

Wiring

There are two options to wire the emergency switch. Option 2 is the recommended version. If you realize version 1, don´t forget an external accessible power-Switch (close to "connector") .

Chassis2021EmergencyStop.png

Case assembly

  • Arrange parts and drill two holes for bumper cabling (see right hand finger for one of the marks)

  • Mount profiles to baseplate and gear-motors to side walls (with especially marked screws "Motor")

  • Mount profile for mowing motor

  • Install sealing ring

  • install mowing motor

  • mount sidewalls

  • prepare backside

  • install backside

  • prepare bumper

  • start with screws -> washers -> plastic spacer sleeves

  • add bumper -> washers -> nuts

  • finished bumper

  • install mowing plate

  • install frontplate

  • finished case

  • install electronics

  • final frontplate

  • final backplate

  • final top view

Motor bearing is stiff

Replace motor bearing by a new one:

mower motor bearing type: 608-ZZ (22mm diameter, 7mm width, 8mm hole)

Further links

instructions on ardumower forum

Von „https://wiki.ardumower.de/index.php?title=Chassis_2021&oldid=10061“