Soldering The Sender: Unterschied zwischen den Versionen
Aus www.wiki.ardumower.de
Roland (Diskussion | Beiträge) K |
Roland (Diskussion | Beiträge) K |
||
Zeile 1: | Zeile 1: | ||
The soldering of the sender will be described. | The soldering of the sender will be described. | ||
− | |||
+ | There are two options soldering the sender | ||
+ | a) Use the DC/DC Converter for Vin and GND of the MC33926 motor driver. This is the default Ardumoer configuration. | ||
+ | b) Use an external powersupply for Vin and GND of the MC33926 motor driver. Then you solder three terminal connectors on the motordriver. With this configuration you can adapt the voltage for the perimeter siganl in a wider range. 5V to 24V for example. | ||
+ | |||
+ | The potentiometers will not be soldered because they have no function. If you want to install them you can do this. | ||
[[File:SenderSoldering1.JPG|none|thumb|Solder 560 Ohm resistor|800px]] | [[File:SenderSoldering1.JPG|none|thumb|Solder 560 Ohm resistor|800px]] | ||
Zeile 13: | Zeile 17: | ||
[[File:SenderSoldering9.JPG|none|thumb|Solder the terminal blocks|800px]] | [[File:SenderSoldering9.JPG|none|thumb|Solder the terminal blocks|800px]] | ||
[[File:SenderSoldering10.JPG|none|thumb|Solder fuse holder|800px]] | [[File:SenderSoldering10.JPG|none|thumb|Solder fuse holder|800px]] | ||
− | [[File:SenderSoldering11.JPG|none|thumb|Solder socket strips for INA and | + | [[File:SenderSoldering11.JPG|none|thumb|Solder socket strips for INA and MC33926 motor drive|800px]] |
[[File:SenderSoldering12.JPG|none|thumb|Solder pins to DC/DC converter and then put a socket on|800px]] | [[File:SenderSoldering12.JPG|none|thumb|Solder pins to DC/DC converter and then put a socket on|800px]] | ||
[[File:SenderSoldering13.jpg|none|thumb|Put the DC/DC converter on the board|800px]] | [[File:SenderSoldering13.jpg|none|thumb|Put the DC/DC converter on the board|800px]] | ||
Zeile 26: | Zeile 30: | ||
[[File:SenderSoldering22.JPG|none|thumb|Install the INA and solder it|800px]] | [[File:SenderSoldering22.JPG|none|thumb|Install the INA and solder it|800px]] | ||
[[File:SenderSoldering23.JPG|none|thumb|Put in the pins fot the mc33926 motor drive|800px]] | [[File:SenderSoldering23.JPG|none|thumb|Put in the pins fot the mc33926 motor drive|800px]] | ||
− | [[File:SenderSoldering24.JPG|none|thumb|Install the motor driver and solder it. Solder also the two right pins. I didn't it here because I want to connect a second external power supply|800px]] | + | [[File:SenderSoldering24.JPG|none|thumb|Install the motor driver and solder it. Solder also the two right pins. I didn't it here because I want to connect a second external power supply -see last picture|800px]] |
[[File:SenderSoldering25.JPG|none|thumb|Solder the terminal blocks. You have two pins soldered between the terminal blocks |800px]] | [[File:SenderSoldering25.JPG|none|thumb|Solder the terminal blocks. You have two pins soldered between the terminal blocks |800px]] | ||
[[File:Ardumower sender pcb.jpg|none|thumb|Board with all components|800px]] | [[File:Ardumower sender pcb.jpg|none|thumb|Board with all components|800px]] | ||
− | [[File:SenderSoldering26.JPG|none|thumb|Three terminalblocks installed on the motor driver because I want to use a second external powersupply for the perimeter signal|800px]] | + | [[File:SenderSoldering26.JPG|none|thumb|Three terminalblocks installed on the motor driver because and Vin and GND of the motordiver are not connected to the sender board. This is because I want to use a second external powersupply for the perimeter signal|800px]] |
Version vom 10. Juni 2018, 14:51 Uhr
The soldering of the sender will be described.
There are two options soldering the sender a) Use the DC/DC Converter for Vin and GND of the MC33926 motor driver. This is the default Ardumoer configuration. b) Use an external powersupply for Vin and GND of the MC33926 motor driver. Then you solder three terminal connectors on the motordriver. With this configuration you can adapt the voltage for the perimeter siganl in a wider range. 5V to 24V for example.
The potentiometers will not be soldered because they have no function. If you want to install them you can do this.